Why would the OEM remove the Seat and make it a Helmet holder with Wire? I can't think of anything other than Cost, but I'm going to launch it as a Tourer and put the luggage in the Tandem seat. You don't think there's anything to print... OEM Helmet holder that you can't use when you load up on the Seat for example, touring
It's a grandchild's product that will help you get your itchy hands on. The Helmet holder works normally with this.
The U-shaped Hook is nice and easy to use, rather than the straight bar that OEMs often use.
I bought it because the AGRASHelmet lock listed GSX250R as well as GSX-S750, so I thought KIJIMA would be attached as well. (AGRAS is expensive).
KIJIMAHelmet lock for GSX-S750, also in Manufacturer's official Out of stock. I couldn't find any in stock at mail order site with the description. If you are planning to buy GSX-S750, please refer to this page.
The footpeg was co-tightened with a screw lock and tightened at 20 Nm. The reason for the 20Nm is that GSX250R had such instructions in the Instruction Manual. Then, I thought GSX-S750 should be the same.
I am glad to know that GSX-S750 has few Other Brand Products and many manufacturers are out of stock.View Detail
The reason for the 4 stars on the installation is that there was some interference with the MotorcycleBody when it was installed. When I used two Bolt points of Tandem Footpeg to fix it, I tried to shift it so that interference would not occur, and to fix it, but sufficient clearance was not taken and it contacted. It may be changed by the individual difference of the motorcycle, but as a countermeasure, it may be necessary to put a washer between them. Other than that, I'm happy with the design of the Helmet as it doesn't fall off when you open the door.
Also, it may be a digression, but please be careful not to lick the Bolt that holds the Tandem Footpeg in place because it contains a locking agent.View Detail
Easy to install and good feeling. Since Tandem FootpegFixing Screw that is reached uses a Screw lock, it is hard to use Hexagonal Wrench so long it is better to use Socket wrench. Gold amount is cheap, but it is enough without cheapness.View Detail
Installation of the product is very easy. Also, the delivery of the product is very fast, and the product description page and configuration are the same.View Detail
Quality and texture information Rubber-covered wiresthe right length to useDesign Information Loop LineSize Chart Information 44 cmExcellent cost performance and comparison with other productsWeBike packaging is always great. Arrives in a week for delivery and packagingConcerns, caveats, or advice on purchasing The helmet holder on the Monkey 125 fits in a really crazy place. So you can't wear a helmet without this wire. I really recommend it I bought two, and I'm using one as a side bag and one as a helmet lock The side bag comes off while driving, so you can fix it and use itView Detail
Quality and texture information is well finished in chromeThe helmet lock has become easier to use for the feeling of use Product to buy together Product # P00040 makes it easy to fix your helmet It's difficult to install Cost performance and comparison with other products, but with high completeness About Shipping and PackagingThe concern when purchasing is that collecting and purchasing information first can save time and money to see if it is possible to install I bought this product because I couldn't use the std helmet lock of Monkey 125, but I'm satisfiedView Detail
Super super fast delivery. This the 3rd or 4th I have ordered (I have owned several Zx14r's and they make good gifts). They fit perfect in the slot. Factory look. First I take the lock to a local locksmith to have him match the key to the ignition key, 10 min and 10 dollars. Bradley needed item on the otherwise perfect bike.View Detail
Quality and texture information Rubber-covered wiresbe adequate in length for use Design Information Loop Wire Size Chart Information 44 cm Good cost performance and comparison with other productsWeBike packaging is always great, arriving in a week for delivery and packagingConcern, caveats or advice on purchase The helmet holder on the Monkey 125 is mounted in a truly ridiculous place So you can't put a helmet on without these wires I really recommend itView Detail
?attachment The CBR650R is mounted at the same position angle as the NORMAL. However, when the handlebar was cut to the Left lock, it interfered with the interior cover next to the Meter, so the interior cover was cut away. I also purchased a 45° angled banjo adapter for the mesh hose to accommodate the tension of the mesh hose. ・NORMAL (Reserve integrated horizontal master) Impressions of No complaints on public roads. Familiar feel and very easy to handle. However, when the brake is set to "hard brake," the rate of increase in braking force relative to the input seems to decrease, and the brake becomes more forceful. Radipon (Reserve separate body portrait master) Impressions of It was totally different from what I expected, my expectation was that it would feel like a Rear brake… It is really a mild and easy-to-handle radipon. On public roads, it feels like NORMAL! I wonder if it's because NORMAL is the same NISSIN? But I felt the radipon effect from Breaking a little stronger, and It can be hung up to a hard brake without effort. I felt trust that this could stop.View Detail
I purchased this for use with multiple Helmets. 。 Mount included with the BOLD. Microphone and speaker are not included and must be purchased separately.View Detail