*图片中的保险杠是为iphone14 pro设计的,附件是moft制作的卡套。
* 仅仅是垫片和螺栓并不能防止镜片干涉。
如果使用铝制垫片来避免与镜头接触,则不能使用,因为螺栓的长度会不足。
*关于qi-compatible无线充电器:安装协作产品等所附的铝制面板时,无法进行充电 请使用附在iphone上的正版Lightning线为电池充电。
*(注1)保险杠的厚度将导致iphone与支持Qi的无线充电器的距离为1.5毫米。充电效率可能比密切接触时略低。充电时间也可能有所不同,取决于所使用的支持Qi的无线充电器的输出功率和适配器电压。
**(注2)由于本产品是由铝制成的特性,会在一定程度上阻挡电波,接收电波的性能可能稍差。在无线电接收条件本来就不好的地方,可能很难接收无线电波。在接收正常的无线电信号时没有问题。
* 即使在内部尺寸内,由于形状和其他限制,我们也不保证所有的玻璃保护膜都能安装。水晶盔甲和钢化玻璃液晶膜不能使用,因为它们比镀金设计的保险杠大。
这个产品是由铝制成的,这意味着无线电波被阻挡在设备的背面。由于产品的性质,它是由铝制成的,这意味着无线电波在产品的背面被阻挡,这可能会稍微降低接收性能。
请注意,gild design不对iPhone主体的任何损坏、故障、丢失、数据丢失等负责。' *本产品不是为了完全保护iPhone免受冲击等。
本产品采用减震树脂设计,以防止保护壳接触到你的iPhone,然而它并不是为了保护你的iPhone不被刮伤。
*请事先注意,gild design不对因连接本产品而造成的iphone主体划痕负责。
* 产品规格、外观和所含附件如有变化,恕不另行通知。
请注意,不得使用外部充电器。
如果你在一个信号不佳的地区,可能很难收到信号。如果你收到的是正常信号,就没有问题。
由于阳极氧化工艺的性质,很难在每个批次中实现相同的颜色。然而,由于阳极氧化工艺的性质,不同批次的颜色有可能不同。
该产品经过阳极氧化处理,所以电流通过的接触点没有颜色。箱子内部有两处未上色的地方,但这不是缺陷。
*我们已尽力使产品图片尽可能接近实际颜色,但由于您的电脑显示器、颜色设置、室内照明和阳光的影响,您可能会感到颜色有变化。
其他颜色可能包括在图像中。
请注意,由于制造商的原因,产品规格可能会有变化。请理解。
[Material]
・Body: A2017S
・Bolt: stainless steel
[Size] 77mm (W) x 153mm (H) x 11mm (D)
[Body weight] 19g
[Product Components]
・Case body 1 set
・5 Torx bolts (including 1 spare bolt)
・5 shock absorbers (including 1 spare)
・5 O-rings (including 1 spare)
Rattle Prevention Kit" (packaged separately)
・3 Torx bolts 7.5mm (including 1 spare)
・Aluminum shim 2mm, 3 pieces (including 1 spare piece)
・Aluminum shim 1mm, 3 pieces (including 1 spare piece)
*The bumper in the picture is for iPhone 14 Pro and the accessory is a card holder made by MOFT.
*Shims and bolts alone cannot prevent lens interference.
*When aluminum shim is used to avoid lens contact, it cannot be used because the length of the bolt is not enough.
*About Qi-enabled wireless chargers: Charging is not possible when the aluminum panel included in collaborative products is attached.Please charge your iPhone with the Lightning cable that comes with your iPhone.
*(Note 1) The thickness of the bumper will cause the iPhone to be 1.5mm away from the Qi-enabled wireless charger.The charging efficiency may be slightly lower than that of the state where it is adhered.The charging time will also vary depending on the output wattage and adapter voltage of the Qi wireless charger you are using.
*(Note 2) Since this product is made of aluminum due to its characteristics, it may block radio waves to some extent and may have a slightly inferior performance in receiving radio waves.It may be difficult to receive the signal in the place where the signal condition is not good.If you are receiving a normal signal, there is no problem.
*We do not guarantee that all the protective glass films can be installed even within the inner dimensions of the case due to the limitations of the shape and other factors.Crystal Armor, tempered glass LCD film cannot be used because it is larger than GILD design bumper.
*Because this product is made of aluminum, radio waves will be blocked from the back of the main body.There is a possibility that the performance of receiving radio waves is slightly inferior.
*This product is not designed to completely protect your iPhone from shocks.GILD design is not responsible for any damage, breakdown, loss, data loss, etc. to the main body of iPhone.
*This product is designed to prevent the iPhone from contacting with the case by using shock-absorbing resin, but it is not designed to completely protect the iPhone from scratches.
*GILD design is not responsible for any damage to the main body of the iPhone caused by the attachment of this product.
*The specifications, appearance, and included products of the product are subject to change without notice.
*You may not be able to use aftermarket chargers.
*It may be difficult to receive the signal in the place where the signal condition is not good.If you are receiving a normal signal, there is no problem.
*Due to the characteristics of the anodizing process, it is difficult to finish the same color for each lot.Tried to keep the same color as much as possible, but due to the anodizing process, the color may vary from lot to lot.
*Because this product is anodized, the contact point where the electric current passes through is not colored.There are two points on the inside of the case that are not colored, but it is not a defect in processing.
*The product image is trying to make it close to the color of the real thing as much as possible, but there is the case that the change of the color is felt by the monitor of the personal computer that the customer uses, the color setting, indoor lighting, sunlight.
*The image may contain other colors.
*There may be changes in product specifications due to the manufacturer's reasons.