12v摩托车型号特定的换挡位置指示器
该表在行驶过程中显示换挡位置。
本套件包括所有必要的安装部件。
包括所有必要的安装部件。
移位数据已被注册。
为汽车模型设计的特殊套件,包含所有必要的零件
为汽车模型设计的特殊套件,注册了w400齿轮位置数据。
使用了每种型号的汽车专用线束,因此您可以轻松地安装该套件,而无需焊接任何东西。
※专用线束有一个12v(+)服务终端,所以你可以轻松地安装cs-550防盗报警器。
●紧凑的设计!
主单元尺寸主单元尺寸为w25.5mm x h30.5mm x d15.5mm(不包括突出部分),设计紧凑,不影响仪表周围的安装。
<
全身上下都有调光感应器调光感应器【自动调光功能】的配备。
调光传感器位于主机的整个表面,可自动将LED的亮度调整为白天较亮,晚上较暗。它能自动调整LED的亮度,"白天更亮,晚上更暗,以提高数字的可见度。
位于主机整个表面的调光传感器允许你酌情设置转速。
当转速上升到超过设定值时,蓝色LED会亮起。
※你可以根据自己的意愿多次重新注册。
该线束连接到仪表背面的黑色12p耦合器上。
工作时间:约60分钟
q&a
q.当车辆钥匙被打开或发动机被启动时,显示屏不工作(led灯不亮)
a.正线或负线可能有接触不良。请再次检查接线。
q.设定档位时,显示 "5"
a.显示 "5 "表示 "s",可能无法接收到速度表信号。
在按下装置背面的开关三次后,将档位挂入一档,换档灯将立即闪烁 "s"。
如果你开始驾驶后,继续出现 "s "显示,请参考以下内容。
如果你有一个电动车速表,请确保线路与车速表电线正确连接。
请检查接线的接触是否有问题。
如果是机械式(电缆式)速度表,请检查来自可选的pg-110的接线是否正确地连接到spi-110的速度表电线。
此外,请检查 "接线 "的接触是否有问题。
请确保磁铁和传感器之间的距离在3-5毫米之内,因为 "s "可能是由于pg-110的主体安装错误而出现的。<另外,请确认每块磁铁的通过点是否通过粘贴在第110页传感器上的蓝色圆形贴纸。
q. 当设置齿轮位置时,显示 "r"。
a. "r "显示表示没有收到发动机转速信号。
请检查接线是否正确连接到转速表的信号线。
b. 请检查接线是否正确。
q. 当设置齿轮位置时,显示 "f"。
a1.在行驶过程中,速度表信号和发动机转速信号都没有被接收。
请检查每条线路的接点和安装方法。
a2.如果在空档以外的档位上打开钥匙,"f "将闪烁。
在这种情况下,请再次将汽车置于空挡,并将钥匙从关闭状态转到开启状态,"f "就不会显示。
a3.如果在空挡下打开钥匙时,"f "仍在闪烁,则说明换挡指示器的绿线没有连接好。
请检查接线图并将其连接到中性开关。
。
12V Motorcycle Model Specific Shift Position Indicator
Meter to display the shift position while riding.
A kit for specific models.
All the parts you need for installation are ALL in ONE.
Shift data has been registered.
●All the necessary parts are included in this kit
●Special design!W400 gear position data already registered!
●Easy installation with special harness!
The special harness is designed for specific model, so you can install it easily without any soldering work.
*The vehicle-specific harness has a 12V (+) service terminal for easy installation of the CS-550 burglar alarm.
●Compact design!
The main unit dimensions are W25.5mm x H30.5mm x D15.5mm (excluding protruding parts), a compact design that does not interfere with installation around the meter.
●LED display for high visibility!
With a dimmer sensor on the entire surface [automatic dimming function]).
The brightness of the LED is automatically adjusted to be brighter in the daytime and darker at night to improve the visibility of the digital numerals.
●Equipped with a shift up indicator!
With a dimmer sensor on the entire surface, you can set the rotation speed arbitrarily to prevent over-revving.
The blue LED will light up when the rotation is higher than the set value.
*You can re-register as many times as you like.
The special harness is connected to the black harness 12P coupler on the back of the meter.
Approx. 60 minutes of work
Q&A
Q. When the vehicle key is turned on or the engine is started, the display does not show (LED light does not light up)
A. The positive wire or the negative wire may have poor contact.Check the wiring again.
Q. When setting the gear position, "5" is displayed
A. The display of "5" means "S", and there is a case that the speedometer signal is not taken.
After pushing the switch on the back of the unit three times, the shift lamp will blink "S" immediately after you put the unit into first gear, but if you start riding and the blinking "S" and the shift lamp disappear and the blinking dot appears and changes to the display of "1" a few seconds later, the unit has been registered without any problem.
If the S display continues to appear after you start running, please refer to the following.
For electric speedometers, check that the wiring is correctly connected to the speedometer wire.
Also, make sure that there is no poor contact between the wires.
In the case of a mechanical (cable) speedometer, check that the wiring from the optional PG-110 is correctly connected to the speed wire of the SPI-110.
Also, make sure that there is no poor contact between the wires.
Please make sure that the distance between the sensor and the magnet is within 3 to 5mm because "S" may appear if the PG-110 is installed incorrectly.
Also, make sure that the passage point of each magnet passes through the blue circle sticker attached to the sensor of PG-110.
Q.When setting the gear position, "R" is displayed.
A. The "R" display indicates that no engine speed signal is being received.
Check that the wiring is correctly connected to the tachometer signal wire.
Also, make sure that there is no poor contact between the wires.
Q.When setting the gear position, "F" is displayed.
A1. While driving, both the speedometer signal and the engine speed signal are not being obtained.
Check the contact of each wire and the installation method.
A2. When the key is turned ON in a gear other than neutral, "F" will blink.
In this case, put the vehicle in neutral gear and turn the key from OFF to ON, so that "F" will not be displayed.
A3. If "F" flashes even when the key is turned ON in neutral gear, the green wire of the shift indicator is not connected properly.
Check the wiring diagram and connect it to the neutral switch.