FAT Swallow専用把手
商品 # HB0294B-10
海淘直邮价(不含运费&税费)
525.74~RMB (9,975 日元)
定价 550.77 RMB 节省 最多 5%
+100~ Webike点数 (5.27 RMB)
当订单生成时,我们将确认制造商的库存并通过E-mail发送预计交货时间给您。
商品 # HB0294B-10
海淘直邮价(不含运费&税费)
525.74~RMB (9,975 日元)
定价 550.77 RMB 节省 最多 5%
+100~ Webike点数 (5.27 RMB)
-材质:不锈钢
-开关孔加工:有
-宽度:730 mm
-高度:40 mm
-向后:65 mm
-向内:约23 度
-把手冠座安装宽度:135 mm
-外径:Φ28.6 mm
-把手内径:Φ18 mm
附仪表上移衬垫
※适合安装2016 年前的车款。
※对应把手内径Φ18mm的平衡端子需要另外购买。
※总宽度变化将产生20 mm或更多的位移量,因此部分零件需要进行位移调整。
※安装参考的商品为黑色。
※商品图片为安装参考。
根据仪表周围细节特别设计的专用把手,直上安装不需要任何修改,紧凑的前配重安装位置!
●与原厂把手相比:
向下约35 mm,向前倾约75 mm。
而左右的宽度缩小约35 mm。
把手角度则向内了约5 度。
附属的衬垫安装后可以将仪表升高,以增加辨识度。
●拉索与煞车油管可以沿用原厂的零件。
●可以同时安装HURRICANE风镜与仪表位移支架。
适配车型链接
最新商品评论或相关商品评论
Perfect bars for my use. Handling was good, more tuck but not bad on back or hips in new position, more than comfortable on my wrists too.
Be warned you will need a plan on moving the cluster over with an aftermarket plate (probably).
Fit is perfect! Drops the riding position a little bit but is not that drastic to the point that you will hurt your back. The pre drilled holes line up to the clutch, brake and throttle controls perfectly. I also purchased the Hurricane clutch cable since the stock one will be a tight fit because of the solid bent portion hear the handebar side. Also, The stock bar end weight will not fit as the hole is 18mm so I am going to purchase a separate bar end weight soon. Without the weight theres a bit more vibration as compared to stock.
为我的2016 FZ-09购买了这些车把,以替换库存车把。 安装非常简单,但是存在一些问题。
制动总泵妨碍了大多数售后市场的挡风玻璃。 我必须拆掉我的
PUIG挡风玻璃,用于安装Hurricane Fat Swallow车把...。
----------------------------------------------
I purchased these for my handlebar 2016 FZ-09, to replace the stock handlebar. Installation is very simple, but there are some problems.
Brake master cylinder prevents the windshield of most aftermarket. I have removed my
PUIG windshield for installation Hurricane Fat Swallow handlebar ....
Powered by Google Translator
Purchased these handlebars for my 2016 FZ-09 to replace the stock handlebars. The installation was very straight forward, but there were a few issues.
1. Stock Brake Master Cylinder gets in the way of most aftermarket windscreens. I had to remove my
PUIG windscreen to install the Hurricane Fat Swallow handlebar.
2. Throttle cables had to be routed above the brake reservoir to prevent the throttle cables from
binding.
3. Had to grind some of the plastic trim around the ignition to provide room for the clutch cable.
4. The stock brake line ends up on a 90 degree bend using the factory setup. Luckily, I'm upgrading
the brake lines to braided stainless steel and will route the front brake line differently.
Otherwise, you will want to disconnect the front brake line and route it differently.
Overall, I am very happy with new sportier ergonomics on the bike that the Hurricane Fat Swallow handlebars provide. Just be warned that you will have to make some modifications for the clutch and throttle cables and be very mindful of the front brake line.
These fit perfectly on my XSR700. The pre-drilled holes lined up perfectly and fitting the bars was very straight-forward.
The bars give the bike a much more aggressive feel but are still really comfortable. They are a huge improvement over the stock bars.
如要继续浏览此商品,请点击"前往Webike日本站",将引导您去Webike日本站(日文)继续浏览此商品。
通知
在您加入购物车前请选择选项。