POSH 通用型 后方向灯支架板
The hole to be tightened with the License Plate Holder is vertical, so there is some flexibility in the mounting position, but the Demerit, which is mounted at an angle, is larger than the License Pla...
The hole to be tightened with the License Plate Holder is vertical, so there is some flexibility in the mounting position, but the Demerit, which is mounted at an angle, is larger than the License Pla...
In replacing the headlightCamaed between homemade Bracket and Light.It was nicely settled.
The Fender Eliminator Kit for Other Brand Products is designed with the assumption of an OEMB blinker, so this is required to install the Other Brand ProductBlinker.
Tres beau produit, connectique et dimension identique à L'OEM. la couleur du cabochon est superbe en rouge cerise. Le montage est realisable avec un peu d'attention. le carrenage arriere se depose par...
The LED tail lamp completes the back of the Z900TS. There are two colors for the case, and for the red product, it shows an accurate matching that is as pure as it is until the lamp lights up.I'm fasc...
The build quality is really good, the LED are bright, and there are separate LEDs for the brake light and licence plate illumination.
While we'll made, the attacked image gives the impression that...
I bought this taillight (smoked option) as the OEM option for my Kawasaki Zr400 x was far too dim.
The product is well made, easy install with no alterations to wiring, includes foam, blackout tape ...
Fit my cabton muffler perfectly. I could not use the original anymore and this was the correct replacement for my peashooter type cabton muffler.
08 KawasakiZrX400 and KOSO (KN Planning) Used in combination with Sequential Blinker inWorked fine.However, the product description does not recommend the use of other manufacturer's blinkers, so the ...
This product can be easily dressed up by replacing rusted screws. It was a good price because there were quite a few in the box!
I used this product as a replacement for Axle Shaft's Split Pin, and the Stainless Steel gives it a more luxurious feel and makes for a nice dress-up!
This product can replace and dress-up the existing Bolt, and it is Rust resistant and highly polished, but it would be nice if it were cheaper!
The Axle Nut on my car uses a Split Pin.It's a pain to change the Split Pin every time I need to do maintenance on my tires, so I bought this Beta Pin to replace it.It's easy to remove and install, an...
The texture wasn't quite as good as I thought it would be, I wish the finish was better.
I don't use it as an ETC Bracket, I use it as a Bracket for additional Meter as the title says.The diameter of the Bolt is the same as the diameter of the Handlebar Switch, so it's ideal for use with ...
Purchased for the installation of the Droreko Camera.The direction of installation may be limited when the license plate holder is large.In the case of my vehicle, I was only able to install it in the...
I bought it as a Loader Hook for the front side of the MT-09.Originally, Loader Hook is attached to Tandem Footpeg, but there is no Loader Hook because Tandem Footpeg has been removed.I found a place ...
I put it on for now.The installation accuracy is no problem because it is only for the car type.As for the position, I think it would have been better to be a little lower & more forward. Well, this i...
The car is limited to the Z900RS and the model EDR-21G, which is as clean as it gets You can install a drorecorderParticularly when it comes to storing the Draco Body, I've been putting it in an empty...
I installed it because I thought it was lonely with the Stand Hook hole, a common 10 for the 6R note that this is an 8mm Stand Hook hole, not amm holeOur Parts were scraped off when it fell over, but ...
There is a storage space of the same size as the product outer dimension in the MC 42.Does Honda contact DAYTONA? It fits perfectly.The box itself is firmly made with a simple drip-proof feeling.The p...
Perfect for JRM-11 made by Japan Radio.Tighten to Clutch lever holder.Just because it is too conspicuous, I'm considering moving it around Meter.
I think that the usability is good because it is lightweight and it can adjust the angle.However, angle adjustment many times (Bending elongation) Then, the surface Anodized (?) It seems Crack is in.T...
如要继续浏览此商品,请点击"前往Webike日本站",将引导您去Webike日本站(日文)继续浏览此商品。