K-FACTORY 离合器连杆
The lever is changed to brembo, but the weight of the clutch holder is still the same as OEM. The weight was still the same. The lever was changed to brembo but the weight of the clutch holder was not...
 |  |  |
| | | |
 |  |  |
| | | |
 |  |  |
| | | |
K-FACTORY 前轮轴防倒球
Purchased for a complete dress-up.As expected, the Gold One point works better than the picture shows.The price seems to be high, but it is not something to be replaced so often. I can't help it becau...
K-FACTORY 打档稳定器
If you use the OEM footpeg, the Shift feel will be harder and you will feel the same whether you have it on or off if you run for 30 seconds, but if you use the Rear Sets, the ShiftStroke will be shor...
K-FACTORY 平衡端子 G Type
This is the KFACTORY Pipe Handlebar that I replaced the other day, and the included Material:The DURACON Bar End was too light, and it vibrated fiercely when I turned more than 8000rpm. when I used OE...
K-FACTORY 二次空气移除盖板
The product that there is Merit of the reduction of the embarrassment etc. by blocking the secondary air introduction. I bought it because I was concerned about the dong dong dong dong dong dong betwe...
K-FACTORY 把手套件
The OEM position of the handlebar is too tight and it puts a lot of stress on your wrist when you ride for a long time. It's not so bad when you ride at high pace, but in the city, it's torture level....
K-FACTORY 打档稳定器
It's a common part, but it's very effective. it's just to put it on the shaft of the clutch, but it makes the shaft stable. It is the same type of shaft, but you can see the effect.
K-FACTORY 脚踏后移套件
Very well done footpegs, easy to install. They allow different positions. Now my bike looks better. Very satisfied of them.
K-FACTORY 排气管垫片 E
Purchased this when I replaced the Full Exhaust System. I think it's reasonably priced.
 |  |  |
| | | |
 | ||
| |
K-FACTORY 把手增高垫片套件
[How is it used?I wanted to adjust the Handlebar.Was the one you received as per Image?＊Image StreetWas the installation difficult?Maybe it depends on how the screw lock works?How was your experience ...
K-FACTORY 排气管贴纸S
I really like the K-FACTORY Emblem with its good design. There is a thin layer of Vinyl on the emblem from the beginning to prevent scratches and other problems. If you try to remove it later, it won'...
K-FACTORY 换档轴支架
To tell the truth, I myself have never experienced GEAR exits with this vehicleWhether this is an individual difference or a difference in Shift change habits is unclearAs far as the Net video is conc...
K-FACTORY 离合器分帮
Beautiful and functional! I purchased this mostly for looks, but it indeed decreases lever pull. Installation is easy and it comes with fasteners and a bleeder.
K-FACTORY 换档轴支架
I've been dissatisfied with the accuracy of KFACTORY's products, even with other productsIt's a shame, because the point of view is good This product is also 1Race and Bearing is outI contacted the Ma...
K-FACTORY 水管 (汽缸-进) 单品
NORMAL is painted on Iron Pipe, but the front wheels are painted with sand and small stones that are rolled up was peeling and rustingIf the rust continues to develop, it will cause water leakage:I re...
K-FACTORY 离合器释放分泵 K Type
It is a rather expensive part, the shape of the part is not so different from NORMAL, and the Clutch I wasn't sure how much lighter it would be, so I was nervous until I actually used itI read somewhe...
K-FACTORY 换档轴支架
Craftsmanship is excellent. Aluminum milling is precise, and anodizing is well done. The spacers are also aluminum (anodized black).
Installation was easy on a 2014 Grom, but I did have one minor p...
 |  |  |
| | | |
 |  | |
| | | |
K-FACTORY 避震器上盖板手
I bought it for Oil exchange.Just by applying to Top cap you can see the goodness of precision.I actually tried opening the top cap, but I think that it is a good item that does not contain any scratc...
 | ||
| |
K-FACTORY 设计帽
The perfection of Cap itself is high, texture is also good.Embroidery of KMark, embroidery of SIDE department is also very polite finish.Although the price is not cheap, it is convincing because thing...
