BORE ACE 打档辅助杆 (BOER ACE 前齿盘外盖对应)
Installed on my 2012 SR400FI with the Collar Set.The description says no modification, but you need to modify the Boots at the back of the Change Pedal. (You just need to cut the tube of the Rubber, s...
 |  |  |
| | | |
 |  |  |
| | | |
 |  |  |
| | | |
BORE ACE 油箱下管散热器
At first I considered the Manufacturer's Oil cooler here. But recently, I thought it was a little too large because I'm running slowly.Then I saw the Heat Radiation Fin for Oil TankDown tube in the Ma...
BORE ACE 打档辅助杆
First of all, it's expensive! 6,000 for all these Parts …Secondly, the installation instructions are unfriendly.The Instruction Manual that came with the Change Accent itself was Only if the Sprocket ...
BORE ACE 握把
Not too soft, not too hard, and the design is simple and cool I went Touring and the Grip is good, it absorbs vibrations reasonably well, and the wrist I wasn't even tired 。 I finally found the Grip I...
BORE ACE 打档辅助杆
I was a little reluctant to use Shift because of the old model, but after I installed this product, it's been a little tougher Chica Chi is now entering It's an inconspicuous part, but I highly recomm...
BORE ACE 进气辅助
The manufacturer's Negative Pressure Adapter to this product The installation is very easy because of the Bolt On However, when 1 pc of an attached bolt is tightened about halfway, it suddenly becomes...
BORE ACE 板材固定用螺丝
Because the OEMs turn the hex heads, there will inevitably be scratches from the opening and closing in the visible areas, but the bore Ace's is a hexagon of holes so you can't see the scratchesThe ri...
BORE ACE 正时链条盖用散热鳍片
It is a fin for better heat dissipation of the Camshaft CoverTo install the Heat Radiation FinBody, remove the Porto and Pipe and Just insert it into the Camshaft Cover from the side, fit the Pipe and...
BORE ACE 汽门检修盖用散热片
Although installation is possible without taking down the tank, it is Large strange to put in L-TypeWrench I struggle withThe Short Neck L-TypeWrench makes installation quite easyI bought it for the m...
 |  |  |
| | | |
 | ||
| |
BORE ACE 负压转接座
If there is enough skill to remove Normal cab, it will easily take youNegative pressure is explained to be connected to Fuel Cock, but I dared to connect to Air inductorSince there is no choice, Fuel ...
BORE ACE FCR用 喇叭口长转接座
Until then, I was using 60 mm Funnel for FCR Carburetor Body 41, but I did not feel the explosion I felt at the time of SCRUp + High Camshaft FCR Carburetor Body 35 I was using at the beginning 'W...
BORE ACE TMR 、FCR 化油器用进气歧管 椭圆型转接座
Until just before installation, there was a doubt - - -I was betrayed in a good way.Torque up. definitely.After all, Manufacturer doing seriously is different ~Number of boa Ace products handledI want...
BORE ACE TMR 、FCR 化油器用进气歧管 椭圆型转接座
No one notices it, but I really like it.I did mirror surface processing myself.The mixture became thinner than originally, but the amount of air is increasing by that amount.You can blow better than t...
BORE ACE TMR 、FCR 化油器用进气歧管 椭圆型转接座
It is dramatically good. After exchange, since an air-fuel mixture becomes thin, change of setting is needed in the direction of deep Sakka. if setting is decided -- Power -- it can blow and stage fri...
BORE ACE TMR 、FCR 化油器用进气歧管 椭圆型转接座
Parts that flow of the air-fuel mixture from a carburetor to an engine will be made into a smooth. It is the feature to carry out elliptic cutting of the admission port, and also it is aiming at the f...
